|
Optronics Test &
Measurement Products
|
 |
OPTMS Single-mode
/Multimode test kit |
Ordering Information
6 |
|
The OPTMS test kit combines the
OPTPM AUTO optical power meter and OPTLS QUAD integrated LED and LASER light
source and is ideally suited for testing fibre optic networks with singlemode
and multimode cables
The OPTLS QUAD features 850 nm and
1300 nm LED output from a multimode output port and 1310 nm and 1550 nm LASER
output from a singlemode output port. The LED and LASER outputs are stabilized
to ensure accurate test results per current TIA/ EIA requirements. This light
source offers 4 modes of operation: Dual wavelengths sending ID, single
wavelength sending ID, CW, and modulated Tone. [Active Output], [Tone],
[Battery], and [External Power] indicators identify the currently enabled
operating mode, battery charge status, and external power presence.
Both output ports are equipped
with removable SC adapter to allow the output connector to be inspected and
cleaned. The OPTPM offers Wave ID, automatic wavelength identification and
switching, when used with the OPTLS QUAD. Multiple test Tone detection is
provided for fibre identification. The OPTM AUTO stores optical references for
each calibrated wavelength. An easy to read Dual Wavelength LCD display with
Backlight shows measured power [dBm or μW] or insertion loss [dB], calibrated
wavelengths, tone signal [Hz], wavelength ID, and the battery charge status.
In addition to being powered by
two AA alkaline, the OPTPM AUTO can be powered by optional AC adapter and/or
rechargeable NiMH battery pack.
|
|
-
Rugged, handheld, lightweight
-
Designed for field use
-
Certify multimode and
single-mode links per TIA/EIA standards
-
Wave ID - automatic wavelength
identification and switching Dual Wave ID, single Wave ID,
CW, and modulated Tone (on
single-mode output)
-
270 Hz, 330 Hz, 1 kHz, and 2 kHz
Tone
-
Large LCD with Backlight
-
Power measurements in dBm or μW;
insertion loss in dB
-
Reference power level storage
-
AA alkaline, optional
rechargeable NiMH battery pack or AC
adapter
-
Low battery indicator
-
Free 50 μm and 62.5 μm mandrels
-
Cost-effective, easy to use
-
N.I.S.T traceable
|
|
Technical Specifications
|
OPTLS QUAD
specifications |
|
Optical |
MM
Optical Port |
SM
Optical Port |
|
Wavelength |
850
± 30 nm |
1310 ± 20 nm |
1550 ± 20 nm |
1300 -10/+50 nm |
|
Emitter type |
LED, Class 1 (IEC 60825 - 1) |
Laser, Class 1
(FDA
21 CFR 1040.10 and 1040.11, and IEC 60825-1) |
|
Output power |
> -
20dBm, 62.5μm Multimode* |
0dBm, 9μm Single-mode |
|
Spectral width (FWHM) |
40
nm (typ) |
120
nm (typ) |
5
nm (max) |
5
nm (max) |
|
Optical connectors |
SC |
SC |
|
Stability |
±
0.1 dB over 8 hours
(after 5 min. warm-up) |
±
0.05 dB over 1 hour
(after 15 min. warm-up)
±
0.1 dB over 8 hours
(after 15 min. warm-up) |
|
General |
|
Power |
2 x
AA batteries, optional NiMH or AC adapter |
|
Battery life |
(2
x AA) Typical 30 hours, Minimum 20 hours Typical 120 hours, Minimum 75 hours |
|
Operating temperature |
-10
to 50°C, 90% RH (non-condensing) |
|
Storage temperature |
-30
to 60°C, 90% RH (non-condensing) |
|
Size (H x W x D) |
5.5
x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm) |
|
Weight |
0.65 lb (.29 kg) |
*
Output power will be approximately 3 dB less if a 50μm mandrel-wrapped jumper is
used instead of a 62.5μm mandrel-wrapped jumper.
All specifications at 25°C |
|
OPTM AUTO specifications |
| Optical |
OPTM AUTO |
|
Calibration Wavelength |
850, 1300, 1310, 1550 nm |
|
Detector type |
Germanium (Ge) |
|
Measurement Range |
+6
to -60dBm |
| Tone detect
range |
+6
to -50dBm +6 to -45dBm for 850nm |
| Wavelength ID
range |
+6
to -50dBm +6 to -45dBm for 850nm |
|
Accuracy (@25°C –10.0dBm) |
±0.25dB |
| Resolution |
0.01dB |
|
Measurement Units |
dB,
dBm, μW |
|
Power |
2 x
AA batteries, optional NiMH or AC adapter |
| Battery life (2 x AA) |
300
hours with backlight [Off]
20 hours with backlight [On] |
|
Operating temperature |
-10
to 50°C, 90% RH (non-condensing) |
|
Storage temperature |
-30
to 60°C, 90% RH (non-condensing) |
|
Size (H x W x D) |
5.5
x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm) |
|
Weight |
0.58 lb (0.26 kg) |
|
* Accuracy measured at 25ºC and -10 dBm per
N.I.S.T. standards.
All specifi cations at 25°C |
|
Ordering Information
|
Descripton |
Part No |
Stk Code |
|
OPTLS QUAD optical light source, OPTM AUTO optical power meter, AA
batteries, Protective rubber boots, adapter cap, 50μm and 62.5μm mandrels,
user guide and carry case |
OPTMSKIT |
190-03D |
Test
jumpers and connector adapters are required for operation (purchased
separately). Test jumpers with a variety of connector styles and fibre types are
available. Adapter caps for most common connectors may be purchased. |
|
|
|
|
